Non Magnetic Whiteboard Wall Covering Lined 1.26m wide

Payment methods accepted by Green Monkey AV Limited

All prices listed exclude VAT.

Bookmark or share this page:

Non Magnetic Whiteboard Wall Covering Lined 1.26m wide

Code:

NMWWL

Description
Specification
Dimensions
Discounts
Delivery
Warranty

Description:

Dry wipe write on whiteboard wall covering surface with feint lines

This versatile and easy to use product offers the perfect solution where a large whiteboard material is required to cover a large surface area.
Supplied on a roll, and attached to the wall using adhesive, the surface allows you to write on / wipe off with dry-wipe marker pens like a standard whiteboard, but is easy to install floor to ceiling, or aross a room horizontally.
High sheen, white gloss dry erase marker surface with protective Teflon coating and write on lines.

Installation is as easy as applying a standard commercial wallcovering. Please see Specifications tab for details. This product can only be hung horizontally. Snap-on trims, pen trays and end caps can be used to finish the edges, and should be installed using the clips provided once the whiteboard wall surface has been installed. The whiteboard wall should be installed using the WWC adhesive.

Please see our range of Accessories for use with this product - Trims, Pen Trays, End Caps, Marker Pens, and Whiteboard Cleaner.

Maintenance
• Install using WWC adhesive
• For writing, we highly recommend the use of our Expo Dry Marker pens. To avoid residual marks, we also advise regular cleaning with our Expo White Board Cleaner. These products are available to purchase as a Starter Kit which contains all the cleaning products you will need for £19 + vat.
• Do not use ballpoint pens or other sharp pointed writing instruments on the Walltalkers surface
• Use non-abrasive cleaners. A household cleaner (eg Windolene) is acceptable. Rinse surfaces thoroughly with water after every cleaning.
• Permanent markings may be removed with alcohol or by writing over the markings with an Expo Dry Marker pen, then wiping clean

Surface Type: Non Magnetic Write on / Wipe Off with Lines

Installation Notes:

General Preperation

• Remove all old backing paper from wall surface. Ensure hanging surface is smooth, clean, dry in depth, of a uniform colour and in a sound condition.
• Surface should be free from contaminants such as dirt, dust, grease, mildew, ink stains etc - any of these can prevent adhesion taking place. Wash with detergent solution, rinse and allow to dry.
• Fill cracks and holes with a proprietary filler in accordance with the manufacturer's instructions.
• Treat any areas showing mould growth.
• Ensure floors are swept clean to avoid dirt gathering at skirting level.
• Ensure that you are installing under adequate lighting conditions.
• Site temperature should not be below 12°C (55°F). Avoid excessive heat until adhesive is fully dried

Surfaces

Plasterboard: File all nail heads, screws, etc. Coat with light coloured oil-based metal primer. All holes should be filled and smoothed. Prime surface with WWC Primer and allow to dry before hanging.

Porous surface (plaster, cement render, etc): Ensure old plaster stable and free of mould. Ensure new plaster dry in depth. Seal with WWC Primer.

Non-porous surface (glass, gloss paint, etc): Abrade surface to provide a key. Wash and dry thoroughly. Use WWC adhesive.

Emulsion paint: Abrade surface to provide a good key. Wash and dry thoroughly. Apply one coat of WWC Primer.

Existing vinyl: Ensure substrate is completely sealed (ie no blown joints, shrinkage etc). Remove all grease, dirt, dust etc - a brush will help in loosening dirt from the crevices of the emboss. Rinse and allow to dry. Hang wallcoverings using WWC adhesive.

Hanging

• Wall Covering with lines should only be hung horizontally.
• Arrange product in roll sequence, starting with the highest number. Cut and hang in sequence, numbering the top of each length to ensure the wallcovering is reversed or not as appropriate.
• Use full widths only. Do not in-fill over doors and windows out of sequence.
• Hang 3 lengths, leave for an hour then inspect. A second opinion may prove useful.
• Phone us on 0845 862 9696 if in any doubt as to whiteboard wall covering's appearance. We cannot accept any claims for more than 3 lengths once material has been cut.
• Continue to check each drop for shading as you proceed.
• With overlap and trim material, overlap by approx. 5cm and trim down the middle. Always use a sharp blade to double-cut or trim material.
• Use wallcovering spatula in up and down direction only. Horizontal smoothing may stretch the wallcovering.
• Avoid getting adhesive on the surface of any wallcovering as complete removal may not be possible.

Dimensions:

This product is supplied on the roll at 1.26m wide, and is purchased per linear meter. Please add the number of meters required by selecting the quantity. Qty 1 = 1 linear meter (1.2m x 1.0m)

Minimum Roll Size = 1.26m wide x 1m length
Maximum Roll Size = 1.26m wide x 23m length
Weight per Square Meter = 381 grammes

Multiple quantity orders:

We offer discounts for larger quanities as shown below:

	1 - 9 linear meters		Full price
	10 - 19 linear meters		5% Discount
	20 - 29 linear meters		10% Discount
	30 linear meters plus		15% Discount

These discounts will be applied automatically when you update the quantity in the shopping cart.

For even larger quantities please email for a quotation or call our sales team on 0845 862 9696

Lead Time:

This product is a stock item and will usually be available for dispatch immediately. However, for up to date stock availability please email or call the sales team on 0845 862 9696.

Warranty:

5 year limited warranty subject to terms and conditions. Please email or call the sales team on 0845 862 9696 to request the full T&Cs.